Millenium BS-2010

205

Speaker Stand

  • For speakers up to 30 kg
  • Material: steel
  • For flange diameter of 25 mm
  • Foot diameter: 1000 mm
  • Extendable from 119 - 200 cm
  • Weight: 2.6 kg
  • Colour: Black
  • Incl. 25 mm diameter adapter for M6 thread (12 mm long)
K dostání od Září 2013
Číslo produktu 320824
Prodejní jednotka 1 ks
Pole diameter 25 mm
2 pieces Set No
Material Steel
Crank No
Ringlock No
Pneumatic No
Feet Tripod
Colour Black
Min. Height 1190 mm
Max Height 2000 mm
Weight per Stand 2,6 kg
Max. Load 30 kg
Zobrazit víc
519 Kč
Cena vč. DPH nezahrnuje poštovné 295 Kč
Množstevní sleva
Cena za kus Ušetříte Množství
519 Kč 1
499 Kč 3,9% 2
Na skladě
Na skladě

Tento produkt je na skladě a může být obratem odeslán.

Informace o expedici
Odešleme pravděpodobně do Středa, 24.04.
1

205 Hodnocení zákazníků

4.4 / 5

Musíte být přihlášeni, pokud chcete hodnotit produkty.

Upozornění: Abychom zabránili tomu, že se budou hodnocení zakládat informacích z doslechu, polovičních pravdách nebo skryté reklamě, dovolujeme na našich stránkách hodnotit pouze skutečným uživatelům, kteří u nás vybavení také koupili.

Po přihlášení najdete také v zákaznickém centru v sekci "Hodnotit produkty" všechny produkty, které můžete hodnotit.

Ovládání

Stabilita

Zpracování

84 Recenze

D
Dávid 13.04.2018
Svoj u?el splni aj ked kon¨trukcia je trochu nestabilna ale do sku¨obne ur?ite odporu?am za ten peniaz.
Ovládání
Stabilita
Zpracování
0
0
Ohlásit hodnocení

Ohlásit hodnocení

google translate gb
Bohužel se vyskyla chyba. Zopakujte protím tuto akci později.
M
Simple stand serving superbly
Michal3806 10.07.2015
as far as stands go, this one will serve you well if you don't put too heavy speakers on top - it's rated to up to 30 kilograms - and is better suited for smaller PA sets.

I purchased this for my Roland Cube CM30 which weighs about 5.5 kilos and is rather small and it feels like a perfect match, not too big, not too small, not too heavy.

Just a word of advice - the 25 mm tube and M6 thread means that for anything else you'll need adapters. I spent a while to get an adapter to the Roland's 3/8 thread but it was my fault, not the stand's. So, to avoid surprises, make sure to check thread compatibility.

But again, if there's a match, this will do the job for a great price.
Ovládání
Stabilita
Zpracování
2
0
Ohlásit hodnocení

Ohlásit hodnocení

google translate gb
Bohužel se vyskyla chyba. Zopakujte protím tuto akci později.
Lm
Speaker stand
Luke malta 21.03.2022
Very stable stand and high quality but the top plastic caps are loose and will stuck to speaker when when speaker removed from stand.
Ovládání
Stabilita
Zpracování
0
0
Ohlásit hodnocení

Ohlásit hodnocení

google translate gb
Bohužel se vyskyla chyba. Zopakujte protím tuto akci později.
A
Good value stand for a small speaker
Anonymní 14.11.2014
I'm using this for a Behringer B205D active monitor that we use as a small PA. The 205D is designer for a mic stand but it felt a bit insecure. This is much more stable and goes a lot higher.

The B205D mounting spigot holds it on a 5/8" mic adaptor leaning back at an angle but I found a microphone table clamp on Amazon which was a short piece of steel channel with a 6mm threaded hole on one flange (for the clamp screw, ideal for the threaded stud on top of the speaker stand cap thingy) and a 3/8" mic adaptor screw on the top. I put it in a vice and bashed the top flange into the right angle to hold the speaker upright, added a 5/8" adaptor and the mounting spigot and it all works well.

So while this is not as light or compact as a mic stand, for most gigs its just right, goes above head height if you need to, and stable enough. If your speaker will fit the 25mm tube, or the 6mm threaded top cap it's fine.
Ovládání
Stabilita
Zpracování
0
0
Ohlásit hodnocení

Ohlásit hodnocení