Kluson MLS33C Lockheads

219

Locking Machine Head Set for Electric and Acoustic Guitar

  • Style: 3 Left / 3 right
  • Closed construction
  • Buttons: Metal style
  • Gear ratio: 1:18
  • Bore: 10 mm
  • Screw tab: 45°
  • Fasten via screws and counter bearing (included)
  • Finish: Chrome
Fås siden Februar 2010
Artikelnummer 241722
salgsenhed 1 stk
Colour Chrome
417 kr
Inkl. moms. Obs! Yderligere fragtomkostninger 60 kr
på lager
på lager

Produktet er på lager og klar til afsendelse.

Information om forsendelse
Afsendelse forventet lørdag, 30.03.
1

219 Kundebedømmelser

4.7 / 5

Du skal være logget på, for at kunne vurdere et produkt.

BemærkVi tillader kun vores kunder, at afgive en vurdering af det udstyr de har købt hos os. Vi modtager ikke anmeldelser eller vurderinger af produkter fra tredje kilde.

Efter login finder du også i kundencenter under "vurderinger af produkt" alle artikler, som du kan afgive en vurdering af.

forarbejdning

125 Anmeldelser

google translate gb
Der opstod en fejl. Prøv igen senere.
TN
Tasos N 21.04.2018
Perfect replacement for a PRS SE. Unfortunately the fact that you need a screwdriver to lock the string has two issues: 1) You have to carry a screwdriver with you 2) You can't really tell if the string is as tight as it should and there is always a possibility to overtighten the screw and break the string as soon as you put enough tension to it. I also think that the edges of the wholes where the string gets in are a bit sharp, which might also cause the string to break.
forarbejdning
1
1
Anmeld bedømmelse

Anmeld bedømmelse

google translate gb
Der opstod en fejl. Prøv igen senere.
N
Kluson for the win
NevermindMe 08.09.2022
I bought a set of these to replace the stock tuners on my Fender CD-60S acoustic guitar. The stock tuners worked just fine, but after 3 years one of them started skipping, so the D string was either a bit sharp or a bit flat. Happy to say that they fit without redrilling, the screws are identical in size and the screw hole was off by less than 1/2 mm, so it worked just fine.
A word of caution when tightening the locking section: first tighten the screw over the string with just your hand, which is enough to hold the loose string. Then use a thin coin (2 cents) or screwdriver for just another 1/4 turn; a 1/2 turn broke my new G string the first time I was installing strings. The thing I like the most is they have very low posts, so no need to wind the string down, there is great break angle over the nut. Just lock it and tune up. For those that like to wind it, there is little space, maybe 1.5 turns on the thicker strings. To be able to have enough room to get a string in safely after installing the tuners, the headstock should not be thicker than 16mm. The caliper says you should be able to use a maximum 0.065 string size.
forarbejdning
0
0
Anmeld bedømmelse

Anmeld bedømmelse

google translate gb
Der opstod en fejl. Prøv igen senere.
A
An upgrade for my Höfner Shorty
Archion 25.09.2021
Bought them as an upgrade for my Höfner Shorty travel guitar. As the original tuners were a bit lumpy I thought if I'm already going to replace the tuners, why not get a locking ones. So far they've been working very well. The only thing is that I'm much more used to locking the tuners with a so called wheel below the tuner. With these there's a thumbscrew above the tuner, which may feel a bit awkward at first. Once you'll get used to it, it works like a charm.
forarbejdning
0
0
Anmeld bedømmelse

Anmeld bedømmelse

google translate gb
Der opstod en fejl. Prøv igen senere.
T
Shaft length 20mm
TeeFon 13.10.2020
These machine heads are high quality. They feel sturdy and durable. I am sure they would have been a great upgrade for my newly acquired HB CST24, however shaft length is too short for the CST24. I was really gutted cause I really wanted to install them.

Only con for me (and why the 4*) is the lack of info on specs incl shaft length which i didn't know was going to be an issue.
forarbejdning
0
0
Anmeld bedømmelse

Anmeld bedømmelse