Göldo E250P

134

Push-Pull Poti

  • 250 kOhm
  • For drawing
  • 2-Way selection switch
  • 6-Pins
Myynnissä vuodesta Joulukuu 2006
Tuotenumero 112185
Myyntierä 1 kappaletta
Design Push Pull
Resistance Value 250 kOhms
Tandem Poti No
Push/Push Push/Pull
Solderless No
shaft type grooved
11,90 €
Sis. ALV. Ei sisällä 12 € rahtikulua
Varastossa
Varastossa

Tuotetta on varastossa ja se voidaan lähettää heti.

Tietoa lähetyksestä
Arvioitu toimituspäivä Torstai, 2.05. - Perjantai, 3.05.
1

134 Asiakkaiden arviot

4 / 5

Sinun pitää kirjatua sisään, jotta voit arvostella tuotteita.

Huomio: jotta vältymme kuulopuheisiin, epätäydelliseen tietoon tai mainontaan perustuvia arvosteluja, niitä saa tehdä vain asiakas, joka on tuotteen meiltä ostanut.

Sisäänkirjautumisen jälkeen löydät kaikki arvosteltavat tuotteet kohdasta “Arvostele tuotteita” asiakastililtäsi.

Työnjälki

51 Arvostelut

A
Hyvää peruskamaa
Tuntematon 25.01.2017
Mulla on ollut monta Göldon potikkaa eri kitaroissa ja hyvin ovat toimineet. Ei ole valittamista. Hinta/laatusuhde kohdillaan.
Työnjälki
0
0
Raportoi ongelmasta

Raportoi ongelmasta

J
Ei tullukaan käyttöön
JanneM 29.09.2014
Lojuu jossain käyttämättömänä.
Työnjälki
0
4
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
M
Great Pot, good connections, quality feel.
Milodon 14.09.2018
Very good pot. Used to MOD an old guitar humbucker to coil split.
Very easy to install and use, only CON is it is quite tall! you MAY have to remove some material inside the guitar to make this fit in place of a regular pot.

I had to remove 4mm of material from the body inside my Strat to get the scratchplate to fit level again. This is on a standard USA strat in the VOL position, so as you can see if you are less confident with tools/basic luthiery, maybe ask your local guitar shop to fit it in this case.

Overall though, great sturdy pot which will last for years, great solid feel, no interference on the pickups when it is pulled (unlike some) so would reccommend, just check dimensions first!
Työnjälki
0
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
t
teaberryou 30.06.2020
I really like 99% of Goldo products, but this time it's just a pass. Yes, it got the job done, but it feels a bit flimsy compared to the Allparts and Fender versions. After fitting, the axle has a little play in it, which makes the knob go ka-klunk after I release it. It's the first time I'm using it for my builds (because the Allparts version wasn't in stock), so maybe it's just this piece I have, and not all of them. It's not a deal breaker, but if given the choice I'd stick to Allparts for my builds.
Työnjälki
0
0
Raportoi ongelmasta

Raportoi ongelmasta