K&M 236

180

Extension Rail

  • For 4 microphones
  • Screw-mountable for stands with 3/8" threaded connector
  • 3/8" Knurled thumb screw
  • Material: Anodised aluminium
  • Length: 365 mm
  • Weight: 0.32 kg
Tuotenumero 104885
Myyntierä 1 kappaletta
20,90 €
Sis. ALV. Ei sisällä 12 € rahtikulua
Varastossa
Varastossa

Tuotetta on varastossa ja se voidaan lähettää heti.

Tietoa lähetyksestä
Arvioitu toimituspäivä Torstai, 2.05. - Perjantai, 3.05.
1

180 Asiakkaiden arviot

4.8 / 5

Sinun pitää kirjatua sisään, jotta voit arvostella tuotteita.

Huomio: jotta vältymme kuulopuheisiin, epätäydelliseen tietoon tai mainontaan perustuvia arvosteluja, niitä saa tehdä vain asiakas, joka on tuotteen meiltä ostanut.

Sisäänkirjautumisen jälkeen löydät kaikki arvosteltavat tuotteet kohdasta “Arvostele tuotteita” asiakastililtäsi.

Työnjälki

60 Arvostelut

h
muuten hyvä, mutta...
hj123 23.12.2017
3/8" ruuvit joita tässä levyssä tulee mukana neljä ovat tosi lyhyitä. kun yhdistää ne esim 1/4" adapteriin niin ruuvin kierteet eivät kunnolla riitä pitämään sitä enää jalustassa kiinni vaan ruuvi tulee levystä läpi. en ymmärrä miksei ruuvit ole esim 1cm pidemmät kun ei siitä olisi mitään muuta kuin hyötyä. kyllä ne tosin riittää mutta kiristäessä pitää olla tosi tarkka.
Työnjälki
0
0
Raportoi ongelmasta

Raportoi ongelmasta

A
Mainio apuväline stereoäänityksiin
Tuntematon 06.12.2016
Äänitän toisinaan AB-stereona kahdella MKH50:llä tai 60:llä ja kiinnitän ne tähän.

Väliraudassa on neljä ruuvin paikkaa mikkien etäsyyden valitsemiseksi. Levein etäisyys riittää vielä kahdelle MKH60:lle zeppeliineineen.

Omiiin tarpeisiini tämä on sopiva. Tietenkin, jos kaipaa tarkempaa mikkien etäisyyden hallintaa, voi olla järkevämpää hankkia malli, jossa ruuvien etäisyyden voi säätää portaattomasti.
Työnjälki
0
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
L
Great little sturdy and mobile stereo bar
LutherD 28.05.2021
I'm a field recordist and I have used this bar a lot, and dragged it everywhere in the world, into the Savannah, rain forest, Subarctic Tundra, cities, and in the studio. I like it so much, I actually just bought a second one.

It's simplicity is it's strenght. just a strong and sturdy bar that fits into most backpacks, and can take quite a beating. It has the perfect lenght to set up an AB setup, omni or Cardioid, and the middle holes allow you to do an XY or ORTF, and you can put both of those on together.

The connections are great for most microphones, even with small blimps. It's also easy to quickly readjust the mic position. My only problem with it is that is not ideal for mounting two big blimps on for outdoor recording in the wild. While it works, the screws loosen slightly every time you move the setup, and you are readjusting the rig every time. But in all other uses, small blimps, no blimps, it works very well, as long as you can live with the fact that you have to estimate the angles and distances of your mics a bit.

I often just use small lavaliers on it as an Omni AB, and just connect the mics with a bit of electrical tape, or a custom made clip.

For on the road (or rather, off the road), and for this price, this is a great little stereo bar.
Työnjälki
0
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
m
Affordable though perhaps a little inflexible
mjfe2 23.10.2017
We use this all the time for four-mic arrays (e.g. AB omnis flanking an ORTF or XY pair). The maximum width is on the small side for AB imaging, and the middle two threads can be a little far apart for ORTF but on the whole it affords quick setup and is well made.
Työnjälki
0
0
Raportoi ongelmasta

Raportoi ongelmasta