Millenium DS200 Black

147

Table Microphone Boom Arm

  • Aluminium construction
  • Locking centre joint
  • 5/8" threaded connector
  • Table clamp for up to max. 56 mm table thickness
  • Pre-wired with XLR cable
  • Length of upper arm: 43 cm
  • Length of lower arm: 40 cm
  • Maximum load capacity: 1.5 kg
  • Colour: Black
Myynnissä vuodesta Syyskuu 2018
Tuotenumero 437359
Myyntierä 1 kappaletta
Type Microphone Boom
Colour Black
Weight 1,8 kg
Näytä enemmän
69 €
Sis. ALV. Ei sisällä 12 € rahtikulua
Varastossa
Varastossa

Tuotetta on varastossa ja se voidaan lähettää heti.

Tietoa lähetyksestä
Arvioitu toimituspäivä Torstai, 2.05. - Perjantai, 3.05.
1

147 Asiakkaiden arviot

4.2 / 5

Sinun pitää kirjatua sisään, jotta voit arvostella tuotteita.

Huomio: jotta vältymme kuulopuheisiin, epätäydelliseen tietoon tai mainontaan perustuvia arvosteluja, niitä saa tehdä vain asiakas, joka on tuotteen meiltä ostanut.

Sisäänkirjautumisen jälkeen löydät kaikki arvosteltavat tuotteet kohdasta “Arvostele tuotteita” asiakastililtäsi.

Vakaus

Työnjälki

96 Arvostelut

l
Not very good
lemurghandi 22.02.2024
It looks sturdy at first, but the joints are plastic and will loosen however tight you fasten them. So with heavier mics, it is a pain to set up. The cable seems of low quality and the table fastening part ain't the best. I would not buy these again.
Työnjälki
Vakaus
0
0
Raportoi ongelmasta

Raportoi ongelmasta

Fp
Solid choice
Finnish podcaster 23.05.2021
It's good boom arm with basic functionalities. Adjustments are easy, but quite one-dimensional. Still, it gets the job done.
Työnjälki
Vakaus
0
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
P
not bad but room for improvement
PKristoffersson 13.02.2020
I bought this table microphone stand so I could do work either sitting or standing by my desk, depending on whether I would be singing or speaking.

This stand supports my microphone (a t-bone 400) with no issue and the reach is long. However, adjusting it is a bit of a pain. There are three separate joints that need to be tightened. The joint closest to the microphone is rather limited in its range of motion. Also, since all joints are hinge type joints it's not easy adjusting to get the microphone exactly where you want it. Overall it's something one can work around, it just takes time.
2
1
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
S
had this for about 1 year
SixStackJack 06.01.2022
bought this one coas i needed a somewhat cheap boom arm for my AT2020 mic, and it works great, the arm keeps still and its somewhat easy to adjust it to your needs,
i had some problems getting the part where you fasten it to the table to stay in place, so i ended up drilling two holes from the top of the "plate" into the table, and then screw it in :D. now it wont move eaven if there was an earthquake :;D
Työnjälki
Vakaus
0
0
Raportoi ongelmasta

Raportoi ongelmasta