Power Pins Bridge Pin Set V2 BK

94

Power Pin Set for Acoustic Guitar

  • Bridge pins that do not have to be removed to change strings
  • No modifications to the instrument necessary
  • Version 2 with Power Plate under the bridge
  • Increased sustain due to larger contact area
  • Low E- and A-strings are marked with "B", D- and G-strings with "M", and B- and the high E-string with "T"
  • Colour: Black
  • Set of 6 pins

Note: Only suitable for strings up to .012 in thickness

Myynnissä vuodesta Lokakuu 2014
Tuotenumero 343829
Myyntierä 1 kappaletta
48 €
Sis. ALV. Ei sisällä 12 € rahtikulua
Varastossa
Varastossa

Tuotetta on varastossa ja se voidaan lähettää heti.

Tietoa lähetyksestä
Arvioitu lähetyspäivä Keskiviikko, 24.04. mennessä
1

94 Asiakkaiden arviot

4.4 / 5

Sinun pitää kirjatua sisään, jotta voit arvostella tuotteita.

Huomio: jotta vältymme kuulopuheisiin, epätäydelliseen tietoon tai mainontaan perustuvia arvosteluja, niitä saa tehdä vain asiakas, joka on tuotteen meiltä ostanut.

Sisäänkirjautumisen jälkeen löydät kaikki arvosteltavat tuotteet kohdasta “Arvostele tuotteita” asiakastililtäsi.

Työnjälki

74 Arvostelut

M
A good idea but a flawed product
Misukoi 21.01.2024
The quality of the hardware is good, but the product is flawed. You need a high saddle on your bridge or the string break angle will be too low. Also, they advertise to be compatible with a 12 gauge set but my bass E 56 gauge is a though fit.

However, they still solve the problem they promise to solve and I have full confidence these will outlast the guitar they're on. So it's not for everyone, but it's for me!
Työnjälki
0
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
GG
they do the opposite of what they supposed to do
GCH Guitar Academy 06.02.2021
They don't work and they actually reduce the power and tone of your guitar. I did extensive tests, some of which you can find on the GCH Guitar Academy YouTube channel. They lift the anchor point of the strings so they reduce the brake point on the saddle and therefore the amount of pressure the strings put on the saddle. By reducing the pressure the strings put on the saddles you reduce the transmission of sound into the guitar body. I did before and after tests and can confirm THEY DON'T WORK.
Työnjälki
6
1
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
MM
Excellent Upgrade
Mr Marcus 12.03.2022
Have them on my 2 Hummingbirds and just got them for my Jazzmaster Acoustasonic. Such simple mid gig string changes, and stops string tails falling into the delicate electrics of the acoustasonic (a bad design fault on Fenders behalf in my opinion)
Työnjälki
1
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
SW
A must for acoustasonic
Shaun W 17.02.2023
Installed on my paisley pink acoustasonic. These are absolutely essential on these guitars to prevent the ballend from falling into the electronics cavity if a string breaks. Installing was a very straightforward process, I didn't need to use the supplied bar as the acoustasonic has a brass grounding plate under the bridge already. One pin was tricky to place but this was due to my bridge hole being countersunk too deep on one side, I remidied this myself without much difficulty and it does not effect the pins performance. I personally have noticed more resonance and sustain from the guitar. I would recommend these for all acoustasonic or gigging guitars for ease of string changing but I don't think I would put them on my high end acoustics that I use for recording. I'm personally ordering another two sets for my other gigging acoustics.
Työnjälki
1
1
Raportoi ongelmasta

Raportoi ongelmasta