Rockboard MOD 3 V2 TRS & XLR Patch Bay

17

All-in-one patch-bay for pedalboards

  • Suitable for MOD Slots in RockBoard Pedalboards
  • Compatible with a wide range of other pedalboards
  • Acts as a central access point to the effect setup
  • Establishes clear cable routes to and from the pedalboard
  • Removable front panel for mounting on or under pedalboards
  • 3x 6.3 mm TRS thru
  • 2x XLR thru (male front / female rear)
  • 1x XLR thru (female front / male back)
  • 1x DC 2.1 x 5.5 mm hollow plug thru
  • 1x AC IEC thru (male front / female rear)
  • All connections mirrored on the rear side
  • Dimensions with front panel (W x D x H): 175 x 85 x 47 mm
  • Dimensions without front panel (W x D x H): 160 x 85 x 33 mm
  • Weight: 450 g
  • Includes mounting screws, lock nuts and TX wrench

Note: Register your product at www.w-distribution.de/Warranty and extend the warranty to 4 years.

Huomaa Rekisteröi tuote osoitteessa www.w-distribution.de/en/Warranty ja pidennä takuuta 4 vuoteen.
Myynnissä vuodesta Elokuu 2019
Tuotenumero 468599
Myyntierä 1 kappaletta
69 €
Sis. ALV. Ei sisällä 12 € rahtikulua
Varastossa
Varastossa

Tuotetta on varastossa ja se voidaan lähettää heti.

Tietoa lähetyksestä
Arvioitu toimituspäivä Maanantai, 29.04. - Tiistai, 30.04.
1

17 Asiakkaiden arviot

4.6 / 5

Sinun pitää kirjatua sisään, jotta voit arvostella tuotteita.

Huomio: jotta vältymme kuulopuheisiin, epätäydelliseen tietoon tai mainontaan perustuvia arvosteluja, niitä saa tehdä vain asiakas, joka on tuotteen meiltä ostanut.

Sisäänkirjautumisen jälkeen löydät kaikki arvosteltavat tuotteet kohdasta “Arvostele tuotteita” asiakastililtäsi.

Työnjälki

13 Arvostelut

P
I Recommend!
P4nuS2k 17.04.2023
A very good product and easy + quick to install!
Työnjälki
0
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
T
Total disappointment
TsalerA 30.08.2021
This is the reason of my bad evening.
Bought it to use with Rockboard pedalboard + Rockboard PSU. Looks cool, but that's all.
1. You have to do an screw-thread in the native pedalboard fof this thing by youself! Guys at the factory were very busy)) DIY!!!
2. It's patch-bay for the XLRs! Guess what?) XLR plugs do not fit in to the pedalboard holes!
3. Connected this thing to the native RB PSU. And it's very very noisy! Spend an hour looking whats the problem. It's this thing!!! Unpluged PSU fron this thing. connected PSU bypassing this thing, and it become less noisey!

Summary: This thing is patch-bay for xlrs, jacks and power.
You can not use this with XLRs and Rockboard pedalbords. You Can not use this with Rockboard PSU. This thing is useless. Waste of money(
Työnjälki
2
2
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
LR
I love it!
Love Rockboard 02.06.2021
Makes my board a lot neater and it looks cool too! Perfect for singer/guitarists (like me) or anyone that needs a few xlr ports on top of the normal jacks.
Työnjälki
1
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
CM
Extremely useful passive connections
Cian M. 23.12.2023
Needed this for a pedalboard build a few years back and have used it in a few different routing / signal chains since then.
The other rockboard patchbays look great too but this has the perfect connections for me. The Jack's being TRS for stereo or midi control is great. Makes routing a board with midi controls/foot controller so much neater and easier.
It is also nice for putting my amp foot switch, guitar signal and vocal mic outputs all within a few centimetres. Max setting up at the gig feel like no work at all.
Työnjälki
0
0
Raportoi ongelmasta

Raportoi ongelmasta