the t.amp E4-130

98

Quadro Amplifier

  • Power: 4x 130 W per channel at 8 ohm, 4x 200 W per channel at 4 ohm
  • Frequency response: 20 - 20000 Hz
  • Input: XLR
  • Output: Speaker Twist
  • For input channels 1 and 2 as well as 3 and 4 bridged use is possible via switch
  • Protection circuit: DC
  • Short circuit protection
  • Overheating protection
  • Limiter
  • Standby switch
  • Voltage: 230 V, 50 Hz
  • Dimensions: (W x D x H): 482 x 408 x 88 mm, 19" / 2 U
  • Weight: 12.9 kg
Myynnissä vuodesta Joulukuu 2014
Tuotenumero 348232
Myyntierä 1 kappaletta
Power (4 Ohms) per Channel 200 W
Channels 4
Rack Units 2 U
Amp Class Class AB
2 Ohm stable No
DSP/Crossover No
Convection cooling No
Width in mm 483 mm
Depth in mm 408 mm
Height in mm 88 mm
Weight 12,9 kg
Bridged Mode 1
Input XLR 1
Parallel Input 1
Link Out No
Output Speaker Twist 1
Näytä enemmän
249 €
Ilmainen toimitus sis. ALV:n
Varastossa
Varastossa

Tuotetta on varastossa ja se voidaan lähettää heti.

Tietoa lähetyksestä
Arvioitu lähetyspäivä Torstai, 28.03. mennessä
1

98 Asiakkaiden arviot

4.7 / 5

Sinun pitää kirjatua sisään, jotta voit arvostella tuotteita.

Huomio: jotta vältymme kuulopuheisiin, epätäydelliseen tietoon tai mainontaan perustuvia arvosteluja, niitä saa tehdä vain asiakas, joka on tuotteen meiltä ostanut.

Sisäänkirjautumisen jälkeen löydät kaikki arvosteltavat tuotteet kohdasta “Arvostele tuotteita” asiakastililtäsi.

Käyttö

Ominaisuudet

Ääni

Työnjälki

59 Arvostelut

J
Juipe 09.04.2021
Tällä kertaa tuli poikkeuksellisesti simu käyttöön 4 kpl but shakereita ajamaan!! Ajaa asiansa erinomaisesti!!
Käyttö
Ominaisuudet
Ääni
Työnjälki
0
0
Raportoi ongelmasta

Raportoi ongelmasta

A
Hinta/laatu kohdallaan!
Tuntematon 18.12.2016
Ostin atmos-kaiutin käyttöön. Riittävästi ääntä ja hyvän kuuloinen. Vahvistimen sijoittamisessa kannattaa pitää mielessä laitteen jäähdytys tapahtuu puhltimilla ja ne eivät ole ihan äänettömät.
Käyttö
Ominaisuudet
Ääni
Työnjälki
0
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
A
The 4-channel monster
Archyx 18.08.2019
tl;dr : The speaker output wiring is a bit quirky. Lots of gain, possibly not good for sensitive speakers in a smaller room.

I bought this amplifier to have a single amplifier unit to drive a bi-amped passive 2-way speaker setup. The amplifier was driven by a dbx DriveRack PA² (EQ, crossover, driver alignment delay). The only drawback in this application was excessive amplifier gain for the little Black Pearls, since this particular audio setup was not to be played loud. However, another pair of speakers (Radiotehnika S-400 4-way monsters) were perfect to be driven by this amp with both amplifier pairs in bridge mode.

The blowers are audible in a quiet room, but then again, this amp is most likely intended to make the speakers loud before the fans really spin up. Another nice thing is that the automagic stand-by function can be switched off.

It's heavy, too. The case design is such that the amp can be set down on an even hard surface on any of its sides without damage to controls or connectors. Gain controls feel good with a little dampening and have detents.

ATTENTION! Since the observation below is not documented in the manuals, please check the output wiring of your amp before connecting any speakers with any methods not described in the manual! There may be changes between board revisions as products are improved!

So far the only inconsistency between the user manual and the actual device I got is the speaker output connectors. The pairs in them are not connected in parallel as the manual loosely suggests, but are connected so that the second pair (2+, 2-) on ch 1 output matches the first pair (1+, 1-) of ch 2 output. The second pair of ch 2 is left open. (This is actually what I was initially expecting this kind of amp to have!)

This means that you don't need a silly Y-cable for connecting a speaker to a bridged amp as specified in the manual, but connecting the 1+ and 2+ contacts of an odd-numbered speaker output to the speaker's + and - does the trick. Also bi-amping a speaker with dual inputs is easy with just one NL4 SpeakON plug carrying both pairs out of the amplifier.

The same applies to the 3-4 channel pair with the exception that on the ch 3 output connector 2- is connected to 2+ instead of the ground with the other 1- and 2- contacts. This means that both grounds (or "negatives") for bi-amping on ch 3 need to be connected together to 1- instead.

The performance for such a low price tag is great, but you can expect some little quirks like this to come with it.
Käyttö
Ominaisuudet
Ääni
Työnjälki
2
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
M
Manos tzi 08.03.2022
very good for their price
Käyttö
Ominaisuudet
Ääni
Työnjälki
0
0
Raportoi ongelmasta

Raportoi ongelmasta