2. Function

How does an electric guitar pickup work?

There is nothing mysterious about the basic principles of electric guitar pickups. In fact the phenomenon at work here also makes many other devices possible, from the bicycle dynamo to the microphone. The principle responsible is known as induction.

And that term almost immediately brings two other buzz words from applied physics to mind: magnetism and coils - and these are, as you may suspect, the basic components of every magnetic guitar pickup!

A pickup consists of a copper wire coil enclosing one or more magnets. In many models pole screws made of iron are used which connect with a magnet under the pickups to achieve magnetization. But more on that later. The poles have the task of picking up vibrations from each guitar string with pinpoint accuracy. But how do they do this?

This is where induction comes into play...

The movement of the (metal) strings over the magnet/pole pieces disrupts the magnetic field present there, this in turn causes the copper wire to produce a voltage. This is known in physics as induction. Since the strength of the flowing current is directly dependent on the intensity and frequency at which the played string oscillates within the magnetic field, it is possible to convert this disruption, one to one, into an electrical signal. This signal carries all the information needed to be converted into an audible signal by an amplifier.

Some guitars are listed as having active pickups. Aren't all pickups active?

No they aren't. Most of them are actually passive. With an active pickup there is a built-in preamplifier installed in the guitar that ensures noise-free operation and a low-impedance signal which won't diminish regardless of the length of the signal path / cable length.

The pickups on my vintage guitar say ''airbucker'' - is that a good thing?

Depends on what you want really, these will be DiMarzio pickups with a weaker magnetic field, resulting in lower output but a more sustained and dynamic sound.

What do I need an F-spaced pickup for?

F-spaced pickups were created specifically for use with guitars that have Floyd Rose tremolo systems installed. The distance between the two poles is a bit more ample and, as with standard pickups with standard systems, this guarantees the best detection of the individual strings. Depending on the manufacturer, this design is also called a trembucker.

What is special about a MIDI-pickup?

A MIDI-pickup is needed in order to transfer analog data, such as that received from strumming a guitar, to an interface which then converts the information to MIDI data. With MIDI data a synthesizer can play any imaginable sound, this means that there is the possibility to reproduce guitar sounds on a keyboard, for example.

What are RWRP pickups used for?

Reverse Wound/Reverse Polarity pickups are single coil pickups designed specifically for use in the middle position of guitars with a typical 3 single-coil set-up. The coils of RWRP pickups are, as you may imagine, wrapped in reverse and the magnet's poles are reversed in comparison to the standard pickups. This is so that they can be connected with both the bridge and neck pickups to give that typical humbucker effect.

I'm looking for a humbucker that has the same look as a standard single coil pickup - is that possible?

Yes! They even have a special name, ''stacked'' pickups. With stacked humbuckers the coils are placed one over the other, rather than side by side. This way they still have the same look as a single coil pickup.

I cannot get my tube amp to distort correctly - am I using the wrong pickups?

To give amps more power and produce better distortion you can install high distortion pickups which have an especially high output power, helping the amp along so to speak.

How can I know for sure if the pickup is switched out of phase?

Two pickups which are in phase will sound normal - full and clean. Out of phase humbuckers sound thin and nasally. The reason for this is that all the bass and mids get swallowed up in this mode.

To explain the effect better we can use an example with speakers: when a sound is simultaneously transmitted through two loudspeakers that are working "in phase", it is bold and loud. If the speakers are out of phase the membrane of one speaker moves forward while the other moves backwards. Resulting in a thin and quiet sound.

What does out of phase mean?

To create the out of phase sound two connected pickups work, in simplest terms, against one another. This causes the frequencies to cancel out, giving a thin and piercing sound.

Kapcsolattartód