Palmer PDI-06-8 Ohm

54

Load Box

  • Adjustable in 6 steps (100%, 70%, 50%, 35%, 25%, 18%)
  • Reduces the volume of a guitar speaker at full saturation of the tubes
  • Made for 8 Ohm or 2x 16 Ohm loudspeakers
  • Bypass/ attenuator switch for fast switching between full and reduced output power
  • Input: 1x 6.3 mm jack socket
  • Output for loudspeaker 2x 6.3 mm jack socket in parallel
  • Output impedance: 8 Ohm
katalógusunkba bekerült: Augusztus 2011
Termékszám 268044
mennyiségi egység 1 darab
113 600 ft
Minden ár ÁFÁ-val
Azonnal szállítható
Azonnal szállítható

A termék raktáron van és azonnal szállítható

Szállítással kapcsolatos tájékoztató
Díjmentes szállítás várható időpontja Hétfő, 29.04. és Kedd, 30.04. közt.
1

54 Ügyfelek értékelései

4.4 / 5

A termékek értékeléséhez kérjük, jelentkezz be.

Megjegyzés: Mivel szeretnénk megakadályozni, hogy az értékelések szóbeszéden, hiányos ismereteken alapuljanak, vagy rejtett reklámok legyenek, csak valós ügyfeleink számára tesszük lehetővé értékelések írását, akik valóban tőlünk vásárolták meg a terméket.

A bejelentkezést követően az ügyfélközpontban, a "Termékek értékelése" menüpont alatt megtalálsz minden terméket, amelyet lehetőséged van értékelni.

tulajdonsagok

hangzás

kivitelezés

32 Vélemények

google translate gb
Sajnos hiba történt. Kérjük, később próbálkozz újra.
C
Really good quality
Csubee 28.09.2020
I use it at home with my Peavey 6505 120W + Engl 4x12 Pro.
I needed this, becasue sometime i have to lower the volume on my rig.

My expactations were not really high, becasue You can read everywhere how attenuators affect the sound of your amp, and how bad they are. I can say i was really suprised.

Compared to the natural sound of my amp i can barely tell the difference (Except the volume ofcourse).
I usually use it on 50% or 75% to attenuate the volume for normal room use, but using on 18% give me a surrealistic feel, becasue i never had a chance to play my amp monster late night. Now its not a problem anymore. At 18% the sound gets a little bit muddy (But still enjoyable) but im sure about its becasue the signal at this level is too low for my 4x12.
The construction is perfect for me. Simple, strong and straightforward. I expected it to heat up after a while, but i never noticed it.
The bypass function also working fine and it makes easy to switch between the amp original and the attenuated volume.

So, I can only recommend it if you need to lower the volume on your rig.
tulajdonsagok
hangzás
kivitelezés
1
1
Jelentem!

Jelentem!

google translate gb
Sajnos hiba történt. Kérjük, később próbálkozz újra.
A
Best attenuator on the market!
Anonim 07.06.2015
Small, simple to use and decent volume differences.

It's fantastic for live shows, I usually set it on 50% with my Mesa Boogie dual Rectifier. It keeps the levels between the different amp channels EXACTLY the same. I've found that some others change the levels for solo boost and clean a fair bit.

Great tone at low volumes!!

It's made by Palmer, so it's a bit pricey, but you get what you pay for!!
tulajdonsagok
hangzás
kivitelezés
2
0
Jelentem!

Jelentem!

google translate gb
Sajnos hiba történt. Kérjük, később próbálkozz újra.
J
Solid design
Joffen 28.08.2020
It does what it's supposed to do, and appears to be built like a tank.
tulajdonsagok
hangzás
kivitelezés
0
0
Jelentem!

Jelentem!

google translate gb
Sajnos hiba történt. Kérjük, később próbálkozz újra.
s
does the job!
sallikaan 11.10.2018
great attenuator for my beast tube amp. german tech, german tank ;)
tulajdonsagok
hangzás
kivitelezés
1
1
Jelentem!

Jelentem!