K&M 21105 Counterweight

164

Balans gewicht

  • Voor gebruik bij zware microfoons
  • Geschikt voor alle eendelige K&M zwenk armen met 3/8" schroefdraad of buis met een diameter van 15 mm
  • Eenvoudig te monteren
  • Extern: 46 mm
  • L: 60 mm
  • Gewicht: 0,8 kg
  • Kleur: zwart
Leverbaar sinds Januari 2008
artikelnummer 200891
verkoopseenheid 1 stuk
€ 16,60
Incl. btw plus € 5,90 verzending
direct leverbaar
direct leverbaar

Dit product is op voorraad en kan direct verzonden worden.

Informatie over de verzending
Levering verwacht rond Vrijdag, 26.04.
1

164 Klantenbeoordelingen

4.8 / 5

U moet ingelogd zijn om producten te evalueren.

Note: Om te voorkomen dat evaluaties gebaseerd zijn op roddel, geruchten of heimelijke advertentie staan wij op onze website alleen evaluaties toe van daadwerkelijke gebruikers die het geevalueerde product bij ons gekocht hebben.

Na inloggen vindt u alle producten die u kunt evalueren ook onder “Product evalueren” in uw klantencentrum.

afwerking

94 Recensies

B
Not only for K&M boom arms
Blickfanger 23.12.2015
I am using this counterweight to balance a microphone array that I made out of Manfrotto Dado balls and rods. the counterweight fits EXACTLY around the Dado rods and can only be slipped on from one end of the rods. This actually is very handy, because when organised properly the weight will never fall off the rods, even when you loosen the knob.

The K&M counterweight is very well made, looks sophisticated and feels particularly nice in the hand. It contains a plastic tube inside the weight's hole that will protect rods or boom arms from being damaged by the locking screw.
afwerking
2
0
Evaluatie melden

Evaluatie melden

google translate gb
Helaas is er een fout opgetreden, probeert u het a.u.b. later nogmaals.
B
The missing link
Ben27 26.01.2021
Used on some (non K&M) stands in order to counter balance my heavier mics.

Most mic clutches tend to give over time, and this counterweight is the ideal counter to that. I don't think you'll ever be able to perfectly balance with one, but they take a lot of the stress out of the central clutch rubber.

Simple to install too - remove anything from the mic stand's boom, slide this on, reassemble. Solid weight and can be used to settle arguments with drummers.
afwerking
2
0
Evaluatie melden

Evaluatie melden

google translate gb
Helaas is er een fout opgetreden, probeert u het a.u.b. later nogmaals.
D
Very useful for balancing a boom
D_C 31.12.2020
Many microphone boom arms lack a counterweight to balance the microphone. I've seen people using extreme force to tighten the main locking screw to try to stop the boom drooping, which can damage the washers. With proper use of a counterweight, far less force is required. Two things are required to use this product: Firstly it is important to check that the boom has a diameter of 15mm. Secondly, it must be possible to slide the counterweight on to the pole. For a telescopic boom, I remove the plastic hand grip off the end (which can require a strong grip to twist it off) and plug the tube with a 15mm end cap (available on ebay). The counterweight can then be positioned close to the end if required.
afwerking
0
0
Evaluatie melden

Evaluatie melden

google translate gb
Helaas is er een fout opgetreden, probeert u het a.u.b. later nogmaals.
m
Improves standard mic stands
mjfe2 23.10.2017
We got one of these to 'upgrade' a hybrid stand consisting of a tall Manfrotto base and a conventional boom arm. The stand now works nicely for drum overhead duties where you wouldn't trust a normal stand to hold up a LDC mic. It's a shame the weight can't go to the very end of the boom arm because most have a lengthy plastic handle in the way but I can't see how else K&M could design the fixture.
afwerking
0
0
Evaluatie melden

Evaluatie melden