EMG PA2

76

Preamp / Booster Circuit

For active and passive pickups

  • Suitable for guitars and basses
  • Boost 0 - 20 dB
  • 1 Mini switch circuit
Produkt dostępny od Listopad 2002
Numer artykułu 158344
Jednostka sprzedaży 1 szt.
298 zł
Zawiera podatek VAT, nie zawiera kosztów wysyłki 49 zł
Dostępny w magazynie
Dostępny w magazynie

Produkt jest dostępny w magazynie.

Informacje dotyczące wysyłki
Wysyłka spodziewana do dnia Czwartek, 25.04.
1

76 Oceny klientów

4.7 / 5

Aby wystawić opinię, należy się zalogować.

Informacja: Aby opinie na temat sprzętu umieszczane na naszej stronie pochodziły jedynie od osób mających styczność z danym artykułem, umożliwiamy wystawianie ocen jedynie naszym klientom.

Opinie można wystawiać po zalogowaniu się w centrum klienta, używając opcji "wystaw opinię".

wykończenie

40 Opinie

google translate gb
Wystąpił błąd. Proszę spróbować później.
2
I love this one!
23cm 12.01.2014
This is a great product for giving the guitar the extra bite and mids.

A word of advice: when installing this, don't set the boost at maximum (you'll understand what I'm referring to when you're there). I had it on max and it just made the guitar sound terrible and over distorted (much like the "loudness-mastering" on Metallica's Death Magnetic). Begin at 50%, try the guitar throught the amp and adjust upwards if needed.
Also, think about this before installing it: do you want it to activate when flicking the switch down or up? If you know that, you can put it in the right position from the start.
I wish I had this boost in all my guitars...
wykończenie
2
0
Zgłoś nadużycie

Zgłoś nadużycie

google translate gb
Wystąpił błąd. Proszę spróbować później.
RS
Great but you need an electronics background ....
ROY STONE 14.01.2020
These are brilliant ..... I find that because of the amount of abuse the wiring of the entire guitar takes, you have be able to fault find electronics to do these & be prepared to repeatedly dismantle Strat guitars, which have no easy access panels, just the complete front panel, meaning removing the strings then a complete rebuild to test it
wykończenie
0
0
Zgłoś nadużycie

Zgłoś nadużycie

google translate gb
Wystąpił błąd. Proszę spróbować później.
S
Great on-board booster
SteveRob 05.06.2015
I used this to provide the active boost for an Andy Summers replica Telecaster I built.

It did a great job; I moved the trim pot to a full-size pot to control the boost level just like on Andy's guitar.
wykończenie
1
0
Zgłoś nadużycie

Zgłoś nadużycie

google translate gb
Wystąpił błąd. Proszę spróbować później.
A
Needed it to blend passive and active
Anonimowy 18.03.2015
I got EM81 bridge and two passive.
So i needed a preamp for passives, because blending passive and active is a bad thing (tested it...horrible).
I used the other side of my selector for passives, and put PA2 at this side's output.
And soldered PA2 output and other side of selector output (EMG81 side) between them.

I put both PA2 and EMG81 at 18V (they handle up to 27V), and a 9V-18V switcher instead of tone knob (metalheads don't need tone knobs :D ).

Nice solution to avoid bypassing passive pickups or replacing them by active single coils.
wykończenie
1
1
Zgłoś nadużycie

Zgłoś nadużycie