Göldo Push/Pull Poti E500P

269

Push/Pull Potentiometer E500P

  • 500 kOhm
  • "A"
  • Small model
  • Thread diameter: 8 mm
  • Length: 10 mm
  • Logarithmic
Produkt dostępny od Lipiec 2005
Numer artykułu 183519
Jednostka sprzedaży 1 szt.
Design Push Pull
Resistance Value 500 kOhms
Characteristic Curve Logarithmic
Thread Length 10,0 mm
Tandem Poti No
Push/Push Push/Pull
Solderless No
shaft type grooved
64 zł
Zawiera podatek VAT, nie zawiera kosztów wysyłki 49 zł
Dostępny w magazynie
Dostępny w magazynie

Produkt jest dostępny w magazynie.

Informacje dotyczące wysyłki
Wysyłka spodziewana do dnia Środa, 24.04.
1

269 Oceny klientów

4.3 / 5

Aby wystawić opinię, należy się zalogować.

Informacja: Aby opinie na temat sprzętu umieszczane na naszej stronie pochodziły jedynie od osób mających styczność z danym artykułem, umożliwiamy wystawianie ocen jedynie naszym klientom.

Opinie można wystawiać po zalogowaniu się w centrum klienta, używając opcji "wystaw opinię".

wykończenie

129 Opinie

google translate gb
Wystąpił błąd. Proszę spróbować później.
C
Not recommended
Crancher 24.08.2019
I tried to install 2 of these on my Jackson, one didn't work and I broke the second one (my mistake). Replaced them later with push/pull CTS pots, the difference in quality is staggering. I'm no longer buying Göldo pots. I'll only recommend these if you are on a really tight budget, but even then I'll look for alternatives.
wykończenie
1
0
Zgłoś nadużycie

Zgłoś nadużycie

google translate gb
Wystąpił błąd. Proszę spróbować później.
n
ncomer 21.12.2015
I wish these would have a more slower turning ease. It is enough to touch the knob and they rotate immediately, and I find this a bit annoying, because I always have to check if the tone is not turned and sucking the... tone out of my pickup. Also, they are not so dirt proof, and within one year or so, you may expect cracks and pops when using the pot side. The switch also "clicks" when pulling it (not when pushing it back); I suppose it has to do with the speed of which I am handling it.

The PRO side, is that it is really indispensable if you want to split coils or want to add some other switching to your guitar.
wykończenie
0
0
Zgłoś nadużycie

Zgłoś nadużycie

google translate gb
Wystąpił błąd. Proszę spróbować później.
P
Thes pish/pull pots in my custom SC-500 II
Properfessor 02.03.2023
I asked them if they could swap out the regular tone pots for these in Sally, my SC-500 II FTF. I use them for splitting the humbucker coils in her.

I see that feature in other HB models such as the CST-24 and I really wanted the same split coil capability in this single cut LP-style axe. It's a one of a kind Custom until someone reads this review.

Thomann's Custom Shop had it done in short order and in my hands 3-4 days later as per their routine business. I did have to buy them of course, but it's the best $12 USD I've spent on guitar accessories in years.
Now I can rock any combination of split coil humbucker in the neck and/or bridge pickup. They're worth every cent
wykończenie
0
0
Zgłoś nadużycie

Zgłoś nadużycie

google translate gb
Wystąpił błąd. Proszę spróbować później.
A
Great push pull pot
Anonimowy 23.11.2014
I purchased this to upgrade my 20 year old HSH jackson and I wanted to be able to turn the guitar into SSS with a pull of a Switch. After extensive research I opted for this one as sold by thomann. During its installation, I would have preferred a better earth lug to be able to solder many wires to. I would say that after installation the pot is very smooth in operation. The volume control on my jackson can sometimes get in the way of playing and I did have a concern that this would be even worse with this new pot in the pulled out position; the reality is that this is no more noticeable than before.
wykończenie
0
0
Zgłoś nadużycie

Zgłoś nadużycie