Jaspers 4D-145B

82

Keyboard Stand

  • For 4 keyboards
  • Made of black powder-coated aluminium
  • Height: 140 cm
  • Width: 155 cm
  • Inner width: 145 cm
  • Maximum adjustable depth: 70 cm
  • With hand wheels
  • The lower section, reinforced by a second tube, has a pair of 60 cm long supports and is also suitable for particularly heavy keyboards
  • The other supports are 40 cm long
  • Load capacity: Lower shelf up to 40 kg / upper shelves up to 15 kg (or more, with shelf reinforcement as below)
  • All shelves are height-adjustable and tiltable
  • Can also be folded for transport
  • Made in Germany
  • Suitable accessories: Additional pairs of shelves, monitor support, micro swivel arm, music stand, laptop shelf (not included)
Produkt dostępny od Marzec 2005
Numer artykułu 176571
Jednostka sprzedaży 1 szt.
Keyboard Supports 4
1 222 zł
darmowa wysyłka, zawiera podatek VAT.
Dostępny w magazynie
Dostępny w magazynie

Produkt jest dostępny w magazynie.

Informacje dotyczące wysyłki
Wysyłka spodziewana do dnia Czwartek, 25.04.
1

82 Oceny klientów

4.7 / 5

Aby wystawić opinię, należy się zalogować.

Informacja: Aby opinie na temat sprzętu umieszczane na naszej stronie pochodziły jedynie od osób mających styczność z danym artykułem, umożliwiamy wystawianie ocen jedynie naszym klientom.

Opinie można wystawiać po zalogowaniu się w centrum klienta, używając opcji "wystaw opinię".

stabilność

montaż

wykończenie

57 Opinie

google translate gb
Wystąpił błąd. Proszę spróbować później.
MG
Works!
M Gho 30.11.2020
Works Perfectly

Only "issue" is that it takes a while to setup

I suggest you prepare the following
1) Cordless Drill with the correct HEX BIT (you will adjusting the fittings a lot)
2) Measuring Tape. This is the only way to get things aligned properly. Make sure each T-fitting is the same distance from the floor (for the left and right A stand) so you end up with a perfect stand
3) Bubble Level. Make sure all your horizontal tubes are level. Also when you are adjusting the holders, You can use the level to make sure the 2 holder arms are parallel. I used an iPhone App, but a bigger physical bubble level will be more useful
4) make sure you jam the fitting into the horizontal bar then u use the locking clamp to make sure it does not twist. Once you do one side, repeat on the other side. Make sure while u are jamming the opposite side, the original side does not pop up. I was lucky my 88 key piano did not drop down the next day. Again double check
stabilność
wykończenie
montaż
3
0
Zgłoś nadużycie

Zgłoś nadużycie

google translate gb
Wystąpił błąd. Proszę spróbować później.
EO
Nothing like Jaspers
Endre Ottem 27.08.2017
I've had this stand for a couple of years now, and I'm absolutely thrilled about it. I have used almost everything there is as far as keyboard stands go, but there's just nothing like Jaspers. The stand is extremely sturdy and the option to add holders makes it very configurable. I currently use it to hold a Motif XS-7 and a Kronos 73 (both very heavy synths) in addition to a lot of smaller synths and controllers. I've added the strengthening set though. I haven't seen any other stands that offer the same flexibility and stability as the Jaspers stands.
stabilność
wykończenie
montaż
1
0
Zgłoś nadużycie

Zgłoś nadużycie

google translate gb
Wystąpił błąd. Proszę spróbować później.
G
Briliant stand when used with care
GilBa 23.09.2023
I ordered this stand and immediately proceeded to put it together without consulting the manual or youtube. What could be hard about setting up a stand right? Wrong move.

I didn't lock the fasting rings, causing my Moog and Minilogue s on the uppermost tier to turn upside down and come sliding down. Just as this was happening, I was holding my Korg M1 that I was trying to insert on a middle tier, creating the crazy situation of me holding 3 synths with nowhere to go. To top it off, my Kronos on the lowest tier came crashing down on the floor because I didn't properly lean the two support beams on the extra lateral beam and didn't set the diagonal sides in the right angle.
I'm telling you this so you may avoid this.

Putting this stand together requires:
- Planning - where do you want to put what piece of gear and at what angle?
- Read the manual or watch youtube howto's first
- Use a spirit level to make sure everything is straight
- Use a centimeter to make sure all the angles are correct and are consistent L/R
- Fasten everything properly using the included hex tool (Be prepared to do a lot screwing as you adjust/perfect your setup)

Once set up, it's a brilliant stand. I love the amount of space at the bottom, I now have a small rack of 19" inch gear there and there's still plenty of room for sustain pedals and so on. The stand is light weight and can be expanded with all kinds of extensions. The lateral beams can be used to esthetically guide cables using cable ties which looks very good (I use Thomann V2030's).
stabilność
wykończenie
montaż
0
0
Zgłoś nadużycie

Zgłoś nadużycie

google translate gb
Wystąpił błąd. Proszę spróbować później.
G
Good 4 keyboard stand
Gibmini 26.11.2019
Pretty stable, even with heavy keyboards like a Kronos. However, there is limited space between the keyboards so it can be hard to see buttons/screens.
stabilność
wykończenie
montaż
1
0
Zgłoś nadużycie

Zgłoś nadużycie

Youtube na ten temat