MJ
Splitter splits like it's supposed to
I bought this splitter after I needed another powersource for my new pedal. My Fuel Tank Junior only had five outputs of 120mA, 9V each. Like I said, I got myself a new pedal which was number six on the board. I figured that I could split the current of one of the outputs and share the current over two low current drawing pedals. Both pedals needed 40mA each, so splitting the 120mA would be a good solution.
I came across this splitter and it seemed to be the one I needed. You really need to carefully read the description of the splitter you are purchasing, because some are designed to split the voltage or even double the voltage. Make sure to choose the right one.
This cable is working fine in my setup. One of the splitters end has a white stripe to indicate that it is groundlifted (to make sure there is no buzz of hum when using it). My signal stayed perfectly quiet so I assume it's doing it's job. I experienced no cons so far.
I came across this splitter and it seemed to be the one I needed. You really need to carefully read the description of the splitter you are purchasing, because some are designed to split the voltage or even double the voltage. Make sure to choose the right one.
This cable is working fine in my setup. One of the splitters end has a white stripe to indicate that it is groundlifted (to make sure there is no buzz of hum when using it). My signal stayed perfectly quiet so I assume it's doing it's job. I experienced no cons so far.
2
0
Zgłoś nadużycie
N
Voodoolab ftw
Voodoolab is the king. Power supply, cables, customer service, support. 5 stars.
#1 voodoolab <3
#1 voodoolab <3
0
0
Zgłoś nadużycie
_
Exsactly what I needed for my pedalboard.
Voodoo Lab easily becomes ''quality guarantee'' name for me.
Voodoo Lab easily becomes ''quality guarantee'' name for me.
0
0
Zgłoś nadużycie
A
Just great for a pedalboard
I use this on my current pedalboard and this splitter is a great addition!
I've done my research on what 2 pedals i can add on one output of my power-supply. So both of my pedals get enough power. There aren't really negatives. If i should give one the splitter could directly go into a pedal instead of needing a second cable.
I used this one because my power-supply is a VooDoo Lab Pedal Power 2Plus. I decided to keep within the same brand because I haven't had any problems with VooDoo Lab so far.
I've done my research on what 2 pedals i can add on one output of my power-supply. So both of my pedals get enough power. There aren't really negatives. If i should give one the splitter could directly go into a pedal instead of needing a second cable.
I used this one because my power-supply is a VooDoo Lab Pedal Power 2Plus. I decided to keep within the same brand because I haven't had any problems with VooDoo Lab so far.
0
0
Zgłoś nadużycie
O
Used it on my cs 12, with good results!
Good quality, also nice because you won't have any ground issues with it. Just remember to watch what ma your power supply actually puts out. Also: the connector is a bit too large for my cs 12 which caused some extra noise, my mistake though. But if you used it on the voodoo lab stuff you won't have any issues!
0
0
Zgłoś nadużycie
TS
excellent cable economy solution
Im use it to power up 2 pedals by 1 DC output of my palmer, very good solution, looks good and durable,I have 3 of them and my power supply have more catering posts so I can put even pedals in my board!
0
0
Zgłoś nadużycie
P
Pedal power
I use two of these adapters very handy. You need to know how much each Ma the pedal needs as the Ma will be shared between the pedals. The cable clips onto the other cable or outlet of my pedal power securely, so no danger of it falling out. I haven't had any problems using them. I would recommend them but do sus out how much Ma you will need, usually written on pedal or in their manual. I contacted voodoo labs for advice and they were very helpful and fast to respond. Would be cool if they did them in different colours so you could easily see which outlet of your power supply it was in.
I use it with tube screamer, tuner and chorus and reverb pedal with no problems with him. Would recommend.
I use it with tube screamer, tuner and chorus and reverb pedal with no problems with him. Would recommend.
0
0
Zgłoś nadużycie
W
Works perfectly
Bought this to power 2 pedals by splitting one output on my Pedal Power 2 Plus. Does exactly what it's supposed to do. No complaints.
0
0
Zgłoś nadużycie
g
very useful
This little cable comes in super handy when you need two pedals on one power output. They work on a single power supply as well as on a Multi-output power supply like a Voodoo Lab pedal power or any other. Low price, high quality. What more do you want?
0
0
Zgłoś nadużycie
e
Life saver!!!
Hi,everyone.If you need to split your currency signal and put it into another effect pedal that is your best option.It is not cheap,but worth it in cases like mine - very tight space and too many pedals.I use mine with VooDoo Lab ISO 5 power brick and it is fits like glove,but i am sure that it would be working with other power supplies too.Like cons i would say,that it seems somehow short and would be nice of VooDoo if they makes cable like this -one short end and one long one.Otherwise very good quality,it is VooDoo after all.Thank you, Thomann about your best services and fast shipment....and for given me choices to choose from.
0
0
Zgłoś nadużycie