Yamaha BMS10A

209

Stand Adapter

Suitable for:

  • MS 20
  • S 15
  • MSP 3
  • MS 101 II
  • MS101 III
  • MS 203 II
  • MG 102 C
  • MG 82 CX
  • Stagepass 400i
  • Stagepass 600i
  • MG 06, 06x, 10, 10xu
Numer artykułu 106561
Jednostka sprzedaży 1 szt.
Electronic Accessories No
Cabinet Accessories No
Stand a. Flying Stud Accessories Yes
275 zł
Zawiera podatek VAT, nie zawiera kosztów wysyłki 49 zł
Dostępny w magazynie
Dostępny w magazynie

Produkt jest dostępny w magazynie.

Informacje dotyczące wysyłki
Wysyłka spodziewana do dnia Piątek, 26.04.
1

209 Oceny klientów

4.5 / 5

Aby wystawić opinię, należy się zalogować.

Informacja: Aby opinie na temat sprzętu umieszczane na naszej stronie pochodziły jedynie od osób mających styczność z danym artykułem, umożliwiamy wystawianie ocen jedynie naszym klientom.

Opinie można wystawiać po zalogowaniu się w centrum klienta, używając opcji "wystaw opinię".

wykończenie

95 Opinie

google translate gb
Wystąpił błąd. Proszę spróbować później.
R
Does the job, very robust, a little finicky
Ruaille 20.01.2019
I got this for the Yamaha MG10XU mixer and it works fine and it is built to last. I used it for pub gigs on a mic stand and the mixer was very secure.

It?s a little bit finicky to attach to the mixer due to the placement of the butterfly heads but once it?s on it?s not going anywhere.
wykończenie
2
0
Zgłoś nadużycie

Zgłoś nadużycie

google translate gb
Wystąpił błąd. Proszę spróbować później.
GM
Good but...
Gavin M. 26.10.2015
This is a great unit that works perfectly when set up, but the set up is hardwork and time consuming. I use this bracket for the yamaha stage pass mixing console.

This bracket is great when assembled, you can turn it to a 45 degree angle and easily access volume, treble, reverb etc. I got it so that the singers I work with would have access to their own sound mix. I use it on a short guitar stand and have it the same height as my keyboard.

The downside is the assembly. I have it permanently attached to the guitar stand but the mixing console still has to have the screws inserted into the back of it - this is a tedious process and takes a few minutes. Often I meet singers right before an event and we have very little time to check keys, run through songs. No way do I have time to start playing with tiny screws, lining them up with the unit, misjudging, starting again.

So overall, great unit, but 4 stars only for the assembly design and set up.
wykończenie
0
0
Zgłoś nadużycie

Zgłoś nadużycie

google translate gb
Wystąpił błąd. Proszę spróbować później.
PA
Mount for stagepass 300
Pat A. 19.09.2013
The attachment does make the system look a lot more neat and tidy when the pa iss mounted on a mic stand, however a good quality mic stand is a must as the stand I first used it on was not that stable. the screws are a bit tricky and there is alway the possibillity of losing one or both. It is such a pity that the mount can not be left on to the pa and stored in the back of the speaker.
wykończenie
0
0
Zgłoś nadużycie

Zgłoś nadużycie

google translate gb
Wystąpił błąd. Proszę spróbować później.
A
High-quality adapter!
Anonimowy 26.09.2016
This adapter is a very good, solid and well-built!

Adapter has an adjustable slope, which is set by the wing nuts on the side. Also, it has two excellent set screws for fixing the monitor on the bottom. It can be set to any microphone stand!
wykończenie
0
0
Zgłoś nadużycie

Zgłoś nadużycie