Göldo MB05C Adapter Bushings

148

Adapter Bushings for Machine Heads

  • Makes it possible to mount vintage-style machine heads with a shaft diameter of 6.4 mm in a bore hole for enclosed machine heads of 10 mm
  • 6 Pieces
  • MB05C
  • Surface: Nickel
Disponível desde Julho 2006
número de artigo 193586
unidade de venda 1 peça(s)
€ 9,90
IVA incluído, € 20 de portes de envio adicionais
Em stock
Em stock

Este produto encontra-se em stock e pode ser enviado imediatamente.

Informações sobre o envio
Envio previsto até Terça, 2.04.
1

148 Avaliações de clientes

4.5 / 5

Terá de iniciar sessão para classificar produtos.

Nota: De forma a prevenir que as classificações sejam baseadas em boatos, conhecimento limitado ou má publicidade nós apenas permitimos classificações provenientes de clientes no nosso website, que tenham adquirido o equipamento através de nós.

Após iniciar sessão poderá encontrar todos os produtos que poderá classificar em classificar produtos no centro de clientes.

acabamento

73 Críticas

a
Nada de errado
alagartixo 27.03.2022
Nada de errado com o produto mas atenção que é possível que não ajustem perfeitamentr nos orifícios do headstock . Comprei para uma Squier bullet e kluson vintage runners e tive que ajustar para ficarem seguros. Mas as bushes sao óptimas.
acabamento
0
0
Reportar a crítica

Reportar a crítica

google translate gb
Infelizmente ocorreu um erro. Por favor tente novamente mais tarde.
TO
Great product - Just not the right fit
Tiago Oliveira Coelho 21.07.2020
Bought a set of Klusons for my Classic 60's Tele (MIM) to replace the Kluson-style Ping/Fender stock tuners, but the bushings were too narrow for the pre-existing holes. So I found these conversion bushings and thought my problem was solved.
Before anything, I have to say that they're quite good, and feel very solid. A+ for building quality.

However, the holes for the tuners in my guitar is neither 8mm nor 10mm. If you have the same model as I do, either be prepared to enlarge the holes on the headstock to fit these, or just use aluminium tape on the narrow bushings to keep them in place.
acabamento
0
0
Reportar a crítica

Reportar a crítica

google translate gb
Infelizmente ocorreu um erro. Por favor tente novamente mais tarde.
t
My bad, they didn’t fit…
tremblox 07.01.2023
These are fine but didn’t fit my application. I’m writing this as a heads-up to others.
Firstly not all tuners, even Gotoh tuners have the same post/shaft diameter. Not even in the same series. Take for example the Kluson-style SD91 series. The units with magnum lock and height adjustable post/shafts - the HAP-M units - have 6mm post diameters. They fit too loosely in these bushings and as a result of the string tension the tuners will get sloppy and wear out prematurely over time.
On the other hand the standard SD91 tuners (no locking, height adjustment) have post diameters of ca 6,25mm (from memory so I might be off by a tad), so that these bushings will be a perfect fit and you’ll enjoy a lifetime of happiness with them.

So in all cases the buyer should check their post diameters carefully before selecting and trying to source the correct bushings. Take care, it’s a jungle out there.
acabamento
1
0
Reportar a crítica

Reportar a crítica

google translate gb
Infelizmente ocorreu um erro. Por favor tente novamente mais tarde.
L
Does not fit all Gotoh locking tuners...
LeonardS 25.05.2021
I bought these to install the Gotoh SD-91-05M MG-T locking tuners as the bushing delivered with the tuners were too small for my Fender to fit well.
However, I can confirm that these Göldo MB05C bushings do NOT fit the tuners either as the diameter, like the Fender ones, are simply too small (narrow).
The Göldo MB05C go well with the other Gotoh SD-91 locking tuners, but for those the Fender bushings fitted as well.
The bushings themselves are ok.
acabamento
0
0
Reportar a crítica

Reportar a crítica