the t.amp E-1200

188

Stereo Power Amplifier

  • Output: 2 x 1200 W at 4 ohm, 2 x 800 W at 8 ohm, 1 x 2400 W at 8 ohm bridged (@ 1 kHz, THD)
  • Frequency response: 20 - 20,000 Hz
  • XLR input and output
  • Input sensitivity: 0.77 V
  • Outputs: Speaker Twist and binding posts
  • Protected circuit design: DC
  • Short-circuit protection
  • Over temperature protection
  • Limiter
  • Amplifier class: H
  • Mains power: 230 V, 50 Hz
  • Dimensions (W x D x H): 482 (19") x 362 x 88 mm
  • Design: 19" / 2U
  • Weight: 15.28 kg
Disponível desde Julho 2019
número de artigo 460282
unidade de venda 1 peça(s)
Power (4 Ohms) per Channel 1200 W
Channels 2
Rack Units 2 U
Amp Class Class H
2 Ohm stable No
DSP/Crossover No
Convection cooling No
Width in mm 482 mm
Depth in mm 362 mm
Height in mm 88 mm
Weight 17 kg
Bridged Mode 1
Temperature controlled fan 1
Input XLR 1
Link Out XLR
Output Speaker Twist 1
Output Binding Post 1
Mostrar mais
€ 268
Envio gratuito, IVA incluído
Em stock
Em stock

Este produto encontra-se em stock e pode ser enviado imediatamente.

Informações sobre o envio
Envio previsto até Sexta, 26.04.
1

188 Avaliações de clientes

4.8 / 5

Terá de iniciar sessão para classificar produtos.

Nota: De forma a prevenir que as classificações sejam baseadas em boatos, conhecimento limitado ou má publicidade nós apenas permitimos classificações provenientes de clientes no nosso website, que tenham adquirido o equipamento através de nós.

Após iniciar sessão poderá encontrar todos os produtos que poderá classificar em classificar produtos no centro de clientes.

manuseio

características

som

acabamento

114 Críticas

DP
Poderoso e nítido
Daniel Pestana 03.10.2020
Poderoso, nítido e construído com robustez. Um equipamento de grande qualidade, que recomendo vivamente. Possui vários tipos de saídas para as mais diversas aplicações.
manuseio
características
som
acabamento
0
0
Reportar a crítica

Reportar a crítica

M
MLSilva 06.06.2023
Não é um som de "topo", mas não fica nada atrás de modelos bem mais caros com características similares. Cumpre muito bem com as especificações anunciadas, boa qualidade de construção e excelente relação qualidade/preço
manuseio
características
som
acabamento
0
0
Reportar a crítica

Reportar a crítica

OS
Amplificador TOP
Oscar Sa 19.06.2022
Exelente amplificador para qualquer tipo de evento!
Potencia mais que suficiente para tudo!
Recomendo!
manuseio
características
som
acabamento
0
0
Reportar a crítica

Reportar a crítica

google translate gb
Infelizmente ocorreu um erro. Por favor tente novamente mais tarde.
B
Only had it a week!
BertyB 29.03.2022
I bought the E1200 to drive a couple of JBL Marquis MS112 as wedges to supplement the powered wedges I already have. The Thoman amp specs are very vague, no mention of RMS or continuous power figures so I took a risk on what the power really was, assuming that for £205 delivered they probably over-state their specs. My main amps are a pair of Yamaha P7000S for FoH so I thought I’d do a direct comparison. Using the sinewave generator in my digital mixing desk I set up a standard config into my Yamahas (set to max gain) into a dummy load, and measured the voltage at the load. The power equation V squared over R gave a power of 180W RMS, bearing in mind the signal output of the sig gen was low-mid level that’s OK. With the same set-up but using the E1200, again set on max gain, the power was over 700w RMS. My dummy load actually started to smoke before I turned it all off. The frequency was a fixed 440Hz, the load was resistive not inductive and I didn’t try any variations, so the power across the frequency range may be quite different. Also, I’m not sure how the input spec varies between the two (-4/+10 dB etc), but my A&H mixer outputs it’s ‘standard’ voltage level regardless the spec of the amp it is feeding, so if that simple test is anything to go by the E1200 seems like a beast, just glad I didn’t bother with the E1500. I’ll probably keep the amp gain levels at half way for the JBL monitor wedges. I also put some music through it connected to speakers but being in my garage at home in a residential area couldn’t crank the level up much so an inconclusive test. Sounded OK to me though. On quality, I immediately noticed that the Chinese ‘speakon’ connectors are not a slick fit like Neutrik connectors. And the XLRs aren’t Neutrik either so expect them to fail, or do as I do and fit a short sacrificial Male-Female XLR cable permanently to the amp so you aren’t continually inserting/removing plugs in your amp, I have found that 1) female XLR pins always fail, and 2) Neutrik connectors last 10x as long as cheap ones.
manuseio
características
som
acabamento
6
0
Reportar a crítica

Reportar a crítica