Millenium DS200 Black

147

Table Microphone Boom Arm

  • Aluminium construction
  • Locking centre joint
  • 5/8" threaded connector
  • Table clamp for up to max. 56 mm table thickness
  • Pre-wired with XLR cable
  • Length of upper arm: 43 cm
  • Length of lower arm: 40 cm
  • Maximum load capacity: 1.5 kg
  • Colour: Black
disponibil din Septembrie 2018
numărul articolului 437359
unitate de vânzare 1 bucată(ăţi)
Type Microphone Boom
Colour Black
Weight 1,8 kg
Mai mult
339 lei
Include TVA la care se adaugă 89 lei costul de transport
în stoc
în stoc

Acest produs e disponibil în stoc și poate fi expediat imediat.

Informații despre livrare
Expediere preconizată până Joi, 25.04.
1

147 Evaluările clienților

4.2 / 5

Pentru a evalua produse trebuie să fiţi logat.

Reţineţi: Pentru a preveni evaluările bazate pe zvonuri sau reclame ascunse permitem doar evaluări de lşa clienţii noştri reali, şi care au cumpărat echipamente de la noi.

După logare veţi găsi de asemenea toate articolele care pot fi evaluate Centrul Logare Clienţi.

Stabilitate

Măiestrie

96 Recenzii

D
Un brat de microfon care imi place !
D?nu? 23.06.2021
Este foarte aspectuos si stabil. Vine din fabrica cu un cablu de microfon pe care eu nu am putut sa-l folosesc, insa asta nu m-a deranjat. L-am schimbat si acum totul este ok. Are un look foarte cool, seamana cu cele de la Mika. Recomand !
Măiestrie
Stabilitate
0
0
semnaleaza un abuz

semnaleaza un abuz

google translate gb
Din păcate a intervenit o eroare. Vă rugăm încercați din nou mai târziu.
P
not bad but room for improvement
PKristoffersson 13.02.2020
I bought this table microphone stand so I could do work either sitting or standing by my desk, depending on whether I would be singing or speaking.

This stand supports my microphone (a t-bone 400) with no issue and the reach is long. However, adjusting it is a bit of a pain. There are three separate joints that need to be tightened. The joint closest to the microphone is rather limited in its range of motion. Also, since all joints are hinge type joints it's not easy adjusting to get the microphone exactly where you want it. Overall it's something one can work around, it just takes time.
2
1
semnaleaza un abuz

semnaleaza un abuz

google translate gb
Din păcate a intervenit o eroare. Vă rugăm încercați din nou mai târziu.
S
had this for about 1 year
SixStackJack 06.01.2022
bought this one coas i needed a somewhat cheap boom arm for my AT2020 mic, and it works great, the arm keeps still and its somewhat easy to adjust it to your needs,
i had some problems getting the part where you fasten it to the table to stay in place, so i ended up drilling two holes from the top of the "plate" into the table, and then screw it in :D. now it wont move eaven if there was an earthquake :;D
Măiestrie
Stabilitate
0
0
semnaleaza un abuz

semnaleaza un abuz

google translate gb
Din păcate a intervenit o eroare. Vă rugăm încercați din nou mai târziu.
M
Solid sturdy build quality, no fiddly wiring or cable tidy to deal with.
Melodyguy 22.03.2022
Needs a good stiff tightening to your studio table. So easy to move about and push mike off side out of use. Really like the black finish, blends well with other equipment.
Măiestrie
Stabilitate
0
0
semnaleaza un abuz

semnaleaza un abuz