Harley Benton Parts Potentiometer A500KOhm

315

Potentiometer

  • Resistance 500 kOhm A-log
  • Small housing
  • Normal toothed axis
  • For assembling on wood
  • Logarithmic
Tillgänglig sedan Januari 2003
Artikelnummer 159774
försäljningsenhet 1 Styck
Design Mini Pot
Resistance Value 500 kOhms
Characteristic Curve Logarithmic
Thread Length 7,0 mm
Tandem Poti No
Push/Push No
Solderless No
shaft type grooved
17,70 kr
inklusive moms, 99 kr frakt tillkommer
Mängdrabatt
Pris per styck Du sparar Summa
17,70 kr 1
16,39 kr 7,4% 4
14,99 kr 15,3% 8
13,59 kr 23,2% 20
i lager
i lager

Produkten finns i lager och kan levereras omgående.

Information om leveransen
Leverans beräknas mellan Måndag, 6.05. och Tisdag, 7.05.
1

315 Kundbetyg

4.5 / 5

Du måste vara inloggad för att kunna betygsätta en produkt.

Obs! För att undvika att betygsättningen är byggt på rykten eller smygreklam kan bara kunder som har köpt produkten från oss sätta sitt betyg.

Efter inloggningen i kundcentret kan du se vilka produkter som kan betygsättas.

hantverkskvalitet

111 Recensioner

EH
Harley Benton Parts Potentiometer A500KOhm
Eric H 03.11.2019
Jag använde den här poten när jag byggde om en Telecaster och det är en tyst och fin komponent. Jag var väldigt noga med att jorda alla höljen och skärmningar och den här fungerar fortfarande felfritt två år senare. Mycket prisvärd.
hantverkskvalitet
1
0
Anmäl recension

Anmäl recension

A
Meh
Arad 29.05.2020
The taper of how it turns the audio signal down is quite weird and sudden.
For example, instead of going from 100% to 0% by going through everything in between, it will go from 100% to 80% and then jump to 30% and stay there for a while before 0. If you are building or fixing a good guitar, go with the Fender pots instead.
hantverkskvalitet
1
0
Anmäl recension

Anmäl recension

google translate gb
Tyvärr uppstod ett fel. försök igen senare.
MM
Good mini-pot, small and short shaft, but works well.
Music Maven 08.07.2019
This is a good quality mini-pot. I purchased this as a replacement for a Harley Benton guitar; it's NOT the same that was in the guitar despite being a Harley Benton product! This is a very small pot! However, as the base is smaller, it's easier to solder as it get's hot more quickly! The full-size units need a more powerful soldering iron. It turns smoothly and functions well. Important: The neck of the shaft is quite short, and it *just* poked through the guitar's top, with enough thread to just get the nut on. If you've got a guitar with a carved or thick top, you'll need a longer shaft for sure. For scratch-plate mounting it should be fine. TIP: You should only ever use "A" log pots for volume & tone, unless you've a vintage "B" linear pot to replace. They just don't work as well. "C" pots are for left-handed players.
hantverkskvalitet
3
1
Anmäl recension

Anmäl recension

google translate gb
Tyvärr uppstod ett fel. försök igen senare.
BI
Trouble-free
Benjamin I. 14.07.2020
My Stagg bass had two broken pots, this one is the replacement for the tone setting. Not much to say, it makes no mechanical or electronic noise, turns very smoothly and the nut and washer assembly is quite firm. The older potentiometer broke when I tightened it moderately, but this one is built tough and accepts being tightened strong without issues.

I suspect my soldering iron is getting old, and doesn't heat up as much as it used too, but the solder flew well and adheres to the tin-plated rings, no problem here.

I noticed no change relative to the older pot except this one is slicker when it turns. Very cheap but very good so I recommend it.
hantverkskvalitet
0
0
Anmäl recension

Anmäl recension