K&M 23325 Table Microphone Stand

328

Microphone Stand

  • Black
  • Cast-iron base with special rubber insert for silencing
  • Screwed, adjustable tube combination
  • Weight: 2.5kg
  • H: 217-347 mm
  • Base-Ø 180 mm
katalógusunkba bekerült: Június 2013
Termékszám 316056
mennyiségi egység 1 darab
Type Desk stand
Colour Black
13 690 ft
ÁFÁ-val, plusz 6 900 ft szállítási költség
Azonnal szállítható
Azonnal szállítható

A termék raktáron van és azonnal szállítható

Szállítással kapcsolatos tájékoztató
Szállítás megközelítőleg Szerda, 8.05. és Csütörtök, 9.05. közt.
1

328 Ügyfelek értékelései

4.8 / 5

A termékek értékeléséhez kérjük, jelentkezz be.

Megjegyzés: Mivel szeretnénk megakadályozni, hogy az értékelések szóbeszéden, hiányos ismereteken alapuljanak, vagy rejtett reklámok legyenek, csak valós ügyfeleink számára tesszük lehetővé értékelések írását, akik valóban tőlünk vásárolták meg a terméket.

A bejelentkezést követően az ügyfélközpontban, a "Termékek értékelése" menüpont alatt megtalálsz minden terméket, amelyet lehetőséged van értékelni.

kezelhetőség

stabilitás

kivitelezés

188 Vélemények

M
Tökéletes
MilanSzakonyi 22.01.2023
Ez a termék strapabíró, stabil, hamisíthatatlan K&M minőség.
Aki ilyen jellegű állványt keres, az nem fog csalódni.
kezelhetőség
stabilitás
kivitelezés
0
0
Jelentem!

Jelentem!

google translate gb
Sajnos hiba történt. Kérjük, később próbálkozz újra.
DD
Feels heavier & sturdier than the photo!
Dr D 01.11.2019
I have a heavy RODE Procaster with shockmount plus TritonAudio Fethead and windshield attached, so I was concerned that a relatively short desktop stand with a not so big base circumference (180 cm or 6-inches) would suffice. Thankfully, I can report that this K&M mic stand is absolutely perfect. It is really quite heavy @ 2.5 Kg ( > 5 lbs) weight, thus can easily cope with more than a kilo of weight up top. In fact, when I grab the head of the mic whilst attached to this stand and try and pull it or tip it over, it just will not.
The other cool aspect of this particular mic stand, is the easily adjustable telescopic pole to adjust the height of the mic. Although it does not increase the overall height by that much, it is sufficient to get the mic up to head head whilst seated at a desk with this stand in front of you. It also secures very well and does not slip or move at all.
Finally, the circular rubber inlay on the rear side of the base, just feels quality - soft but does not allow the stand to slide at all. Even hitting the side of the base with my clenched fist does not move it.
I would highly recommend these K&M mic stands and the next time I shall be in the market for another one, I will look for this brand again.
kezelhetőség
stabilitás
kivitelezés
3
1
Jelentem!

Jelentem!

google translate gb
Sajnos hiba történt. Kérjük, később próbálkozz újra.
N
Doubles as a battel hammer
Nänad 04.01.2021
Seriously, this thing is so sturdy, you can kill a guy with it. Has a rubber layer on the bottom which prevents it from sliding on top of a desk. RODE NT 1 fits perfectly on top of it. Can be used for recording instruments, but for recording conversations as well...and killing people (in which case RODE NT1 should be replace with Shure SM58, due to it's enhanced rigidness)
kezelhetőség
stabilitás
kivitelezés
8
1
Jelentem!

Jelentem!

google translate gb
Sajnos hiba történt. Kérjük, később próbálkozz újra.
r
Its decent
rayzer... 03.04.2022
It has a really heavy base so you wont be knocking it over accidentally but i found it sounded a bit hollow when i first used it by my computer.
After sticking some carpet and rubber squares under it that became a non issue.
Other than that its sturdy and does its job.
kezelhetőség
stabilitás
kivitelezés
0
0
Jelentem!

Jelentem!