the t.bone Microphone Holder Universal

548

Universal Microphone Clamp

  • Clip holder for all standard microphones
  • 5/8" Thread
  • Colour: Black
  • 3/8" thread reducer art. 104948 not included
  • Suitable for microphones with diameters from 1.6 cm to approx. 3.5 cm
Termékszám 105902
mennyiségi egység 1 darab
Component type Microphone Clamp
1 990 ft
ÁFÁ-val, plusz 6 900 ft szállítási költség
Azonnal szállítható
Azonnal szállítható

A termék raktáron van és azonnal szállítható

Szállítással kapcsolatos tájékoztató
Szállítás megközelítőleg Szerda, 15.05. és Csütörtök, 16.05. közt.
1

548 Ügyfelek értékelései

4.2 / 5

A termékek értékeléséhez kérjük, jelentkezz be.

Megjegyzés: Mivel szeretnénk megakadályozni, hogy az értékelések szóbeszéden, hiányos ismereteken alapuljanak, vagy rejtett reklámok legyenek, csak valós ügyfeleink számára tesszük lehetővé értékelések írását, akik valóban tőlünk vásárolták meg a terméket.

A bejelentkezést követően az ügyfélközpontban, a "Termékek értékelése" menüpont alatt megtalálsz minden terméket, amelyet lehetőséged van értékelni.

kivitelezés

170 Vélemények

google translate gb
Sajnos hiba történt. Kérjük, később próbálkozz újra.
A
Do-All Clip
Anonim 06.04.2016
Currently, I am saving for a set of 12-Guage microphones, which are made from spent bullets - If you have not heard of 12-Guage, Google it, they are amazing!

I needed a clip that would hold very-thin microphones so I took 12-Guages recommendation and went for the spring-type clip. Having the need to purchase from Thomann anyway, I thought I would add a couple to my order.

To be honest, I probably wouldn't like a collection of these things. Call me old fashioned but I think the standard mic clip is a better option; but if you have something like a 12-Guage microphone, then these clips are the ones to buy.

Recently, I picked up an EV N/D 257B microphone. These mics have a "Warm Grip", which tends to "go hard, crack and eventually fall off". I bought my EV cheap, second hand, without its "Warm Grip" These mics are the thinnest mics I have ever seen, with the accessory not in place, and I wondered if the Holder Universal would be able to hold the microphone. It does the job, no problem.

I haven't tested it because I haven't got one, but I am guessing it might just fill in as a replacement for an AKG D112's clip. Those clips are around £15 to £18 to replace (new) so this clip could also serve a purpose for those mics whose clips are expensive to replace.

Recommended when a generic clip is your only option but use standard mic clips wherever possible. Next time I order from Thomann, I think I will buy a couple more. Now I am assured of the quality, I think they will be handy to have around.
kivitelezés
0
0
Jelentem!

Jelentem!

google translate gb
Sajnos hiba történt. Kérjük, később próbálkozz újra.
A
Does what its supposed to do
AlexCm 03.02.2019
This clip is made well enough and does the job. It clamps well and has good rubber contact points to protect the mic.
kivitelezés
0
0
Jelentem!

Jelentem!

google translate gb
Sajnos hiba történt. Kérjük, később próbálkozz újra.
AC
Cheap plastic
Anton Cristian Mihail 24.04.2019
The clamp feels very cheap and the platic is rigid.
kivitelezés
0
0
Jelentem!

Jelentem!

google translate gb
Sajnos hiba történt. Kérjük, később próbálkozz újra.
K
Good tool, but could be improved
Knga 18.04.2016
I bought this mic holder to use with various different microphone sizes (Shure SM57, SM57, Sennheiser MD441, PG, ...).

Pros:

You can use this holder for various microphones (if you didn't have this type of holder, you would need to change holders if you would need different microphones).

Cons:

Spring holding 2 sides of holder together should be a bit stronger, to have more firmly tight on microphone and to prevent it from falling down.tgo
kivitelezés
0
0
Jelentem!

Jelentem!