Behringer CM1A

12

Eurorack module

  • MIDI-to-CV interface
  • 16Bit converter
  • Monophonic and duophonic operation possible
  • 2 CV outputs
  • 2 gate outputs
  • Switchable between S-trigger and V-trigger
  • USB-B port
  • MIDI In/Thru
  • Consumption: 70 mA (+12 V) / 10 mA (-12 V)
  • Width: 6 HP
  • Depth: 52 mm
Produkt dostępny od Styczeń 2022
Numer artykułu 523241
Jednostka sprzedaży 1 szt.
Width 6 TE / HP
333 zł
Zawiera podatek VAT, nie zawiera kosztów wysyłki 49 zł
Dostępny za 2-3 tygodnie
Dostępny za 2-3 tygodnie

Produkt będzie za niedługo dostępny i natychmiastowo gotowy do wysyłk.

Informacje dotyczące wysyłki
1

12 Oceny klientów

4.4 / 5

Aby wystawić opinię, należy się zalogować.

Informacja: Aby opinie na temat sprzętu umieszczane na naszej stronie pochodziły jedynie od osób mających styczność z danym artykułem, umożliwiamy wystawianie ocen jedynie naszym klientom.

Opinie można wystawiać po zalogowaniu się w centrum klienta, używając opcji "wystaw opinię".

obsługa

właściwości

wykończenie

9 Opinie

TT
A little bit disapointed
TRIPlets Together 25.09.2023
For one channel it works ok, but does not suport 2 different channels via usb.
obsługa
właściwości
wykończenie
0
0
Zgłoś nadużycie

Zgłoś nadużycie

google translate gb
Wystąpił błąd. Proszę spróbować później.
R
Nice MIDI-CV module. Make sure to calibrate it!
Radu7 25.02.2022
This module made a nice addition to my Behringer System 100 rack setup. Everything worked as designed save a few issues:

1. The Behringer Synthtribe 2.5.7 app constantly crashed and was unusable for configuring the CM1A. Going back to Synthtribe 2.5.5 worked perfectly. I reported the issue to Behringer so perhaps it will be rectified in the next release.

2. The scaling on the CM1A was terrible out of the box. It was unable to play two octaves in tune. This can be corrected using the calibration portion of the Synthtribe 2.5.5 app, but there are no instructions for this and Behringer support appear to be unaware this feature even exists. There is an incomplete diagram on the calibration page for the hookup to your DMM (you need a quality DMM with at least 3 decimal places of accuracy) and the process does not work well if you do not place a load (100KOhm resistor, for example) that approximates the impedance of the VCO you are calibrating the CM1A for.
After calibrating using Synthtribe with a suitable resistor across the DMM test leads it scales across 4 octaves quite well.

3. Does not play well with passive mults at all. This is common with any CV used for pitch control, but the CM1A is very sensitive to this when compared to other MIDI-CV modules I've tested. You need a buffered mult if you need to use the CV outs with more than one input each if you expect accurate scaling when controlling pitch.

None of the 'issues' I mentioned above are out of the ordinary for a MIDI-CV module in general, but could put off someone new to modular synths or cause them to return the module thinking it was faulty when it simply needed calibration, etc...
obsługa
właściwości
wykończenie
8
0
Zgłoś nadużycie

Zgłoś nadużycie

google translate gb
Wystąpił błąd. Proszę spróbować później.
S
TOP QUALITY
Sammysammy1 09.03.2022
Very easy to use and the quality is great
obsługa
właściwości
wykończenie
1
0
Zgłoś nadużycie

Zgłoś nadużycie

google translate gb
Wystąpił błąd. Proszę spróbować później.
e
Compact and reliable
elpero 11.05.2022
USB connection is a nice feature, you can drive the module from PC from VCV Rack for example.
obsługa
właściwości
wykończenie
0
0
Zgłoś nadużycie

Zgłoś nadużycie