Fryette Power Station 100

I bought the Power Station to better utilize my Marshall JMP 2203 100-watt amplifier and it really does what I expected it would, and more. I am now able to record and jam with this amp head at home by plugging it into my audio interface and DAW. I'm using ML Audio impulse responses in Reaper for cab simulation. It's very very nice. The main application for me however is to tame the 2203 in rehearsals or on stage to a desired volume level. With the Fryette I can crank it up how I want, and then adjust the volume from the Fryette controls. The 2203 really needs to be cranked to get it to sound right, and at that point most mixing engineers, my band mates, and even myself will consider that it's just too loud for the stage and space we are playing... The PS solves this 100%. At first I thought the price is quite a lot to pay, but now after I've used the PS for a while I know this money was truly well spent and I can get the most out of the equipment I already had, but just wasn't able to fully utilize. Excellent piece of equipment.

A top-notch quality attenuator, transparent tube power amp and fx-loop in a compact case that fits into 2U height (rackmount kit is sold separately) or on top of a guitar head. Mine comes with matched Sovtek 6550WE power tubes and Ruby 12AX7C5 HG driver & phase inverter tube. According to manual, KT88 tubes can be also fitted without biasing.

I use it with home-built 100W 1959 SuperLead (no built-in fx-loop, no built-in line-out). I needed to solve master volume, post-amp fx-loop, and solo boost. Before I discovered this device, I had to reamp it, which included a load-box for the first speaker out jack (Palmer PDI-06-16), line-out box for the second speaker out jack (served as post-amp fx-loop), and finally solid-state amp to amplify the signal. This was a little bit complicated setup.

I recommend you to set the input and output impedance to match the settings as your amp was connected straight to the speakers, because it is easy to switch the bypass button and you might get into trouble with mismatched impedances between your amp and speakers.

Pros:
+ reactive load. you would hardly hear the tonal difference between bypass and attenuated mode, very transparent
+ adjustable volume from silent recording across bedroom level to full 100W power
+ two channels with individual volume, presence and depth settings, switchable either by front panel button or footswitch (not part of the package). suitable for lead and rythm
+ silent recording option via line-out (balanced or unbalanced), even without powering the device
+ no-load protection (internaly switched speaker jack to a dummy load)
+ separate 2/4, 8, 16 impedance selection for amp in and speaker out
+ bypass the whole thing by a flick of a switch
+ post-amp fx-loop with level settings
+ line-in for connecting any device; e.g., pre-amp, phone, etc.
+ no need to bias
+ ground lift

Cons (very very slight):
- single speaker output. in comparison to PS-2, the second speaker output has been replaced by a footswitch jack for TRS cable to control the FX-loop and channel selection. if you want to connect a full stack (e.g. two 4x12" cabinets), you have to use Y speaker cable or Palmer CAB M Merger
- fx-loop can be switched on/off remotely only; e.g. with a footswitch pedal
- rack mount kit not included

If you have a non-master volume non-fx-loop amp you love to play and you play in a band with other guitarist, this is a must have. You will love it. Period.

Ich suche und verwende schon seit Jahren Attenuatoren (Marshall Power Brake, Marshall SE100, THD Hot Plate, TAD Silencer,...) aber bisher konnte nur der OX klanglich überzeugen.
Bei meinem Lieblingsamp, dem Marshall 1974x gehen beim OX allerdings  ab Stufe 2 deutlich Höhen und Dynamik verloren. Und das ist genau der Bereich, den ich zu Hause nutze. Deshalb habe ich mir als Alternative die Power Station 100 zugelegt.

Was mir als erstes aufgefallen ist, ist das die Power Station 100 ganz schön Gewicht hat. Getestet habe ich sie natürlich an meinem 1974x. Und was soll ich sagen? Ich finde die Power Station 100 klingt großartig. 
Schön transparent, die Dynamik bleibt, auch wenn ich die Lautstärke deutlich reduziere. Und durch die kleinen Soundhelfer Presence, Depth, Brite, Warm lassen sich tonale Abweichungen dezent anpassen, ohne den Klangcharakter zu verändern.
Super ist auch, dass das Gerät einen Bypass hat, sodass man den Originalklang immer wieder aufrufen, mit den "reduzierten" Klang abgleichen und mit den Soundhelfern ggf. dann anpassen kann.
Und zu guter Letzt ist die Lautstärke Regelung stufenlos, was ich beim OX sehr vermisse.
Alle anderen Funktionen (Verstärkung, FX Loop,...) habe ich nicht ausprobiert, weil ich diese Funktionen nicht brauche.

Der OX hat ohne Zweifel auch seine Stärken und ich werde ihn auch weiter nutzen aber die Power Station 100 ist mit seinen Features der best klingende Attenuator, den ich ja hatte.