Doepfer A-162

25

Dual Trigger Delay

  • Allows delayed output of the input signal
  • Power requirement: +40 mA (+ 12V) / -0 mA (-12V)
  • Width: 8 HP / 40.3 mm
  • Depth: 45 mm (measured from the back of the front panel)
K dostání od Říjen 2004
Číslo produktu 154957
Prodejní jednotka 1 ks
Width 8 TE / HP
1 599 Kč
Cena vč. DPH nezahrnuje poštovné 295 Kč
Na skladě
Na skladě

Tento produkt je na skladě a může být obratem odeslán.

Informace o expedici
Odešleme pravděpodobně do Čtvrtek, 2.05.
1

25 Hodnocení zákazníků

4.8 / 5

Musíte být přihlášeni, pokud chcete hodnotit produkty.

Upozornění: Abychom zabránili tomu, že se budou hodnocení zakládat informacích z doslechu, polovičních pravdách nebo skryté reklamě, dovolujeme na našich stránkách hodnotit pouze skutečným uživatelům, kteří u nás vybavení také koupili.

Po přihlášení najdete také v zákaznickém centru v sekci "Hodnotit produkty" všechny produkty, které můžete hodnotit.

Ovládání

Vlastnosti

Zpracování

15 Recenze

google translate gb
Bohužel se vyskyla chyba. Zopakujte protím tuto akci později.
VW
Doepfer support is NON PLUS ULTRA
Vladimir Woelfl 25.08.2021
I modded mine to get really short delays (less than ms), didn't work right at first, but then I got a reply from Dieter Doepfer himself 😁
I did what he wrote me, and now it works exactly as I want it to.

In case anyone else decides to change the timing caps - first note that this *voids warranty*, so if you're not experienced with electronics, don't mess with it.

I used 330nF for C2 and 100nf for C5.
This is what Dieter Doepfer wrote me:

"If the value of capacitor C2 (10u) is reduced too much the first unit (delay) does no longer trigger the second unit because the pulse becomes too short. An additional resistor at the trigger input of the second unit (pin 8 of the NE556) to GND will help to solve this problem (1M should work, we tested it with C2=470nF). In addition the resistor R4 can be increase from 220 Ohm to 1k. R4 defines the shortest time and is in series with the potentiometer."
Ovládání
Vlastnosti
Zpracování
2
0
Ohlásit hodnocení

Ohlásit hodnocení

google translate gb
Bohužel se vyskyla chyba. Zopakujte protím tuto akci později.
A
trigger delay with huge range
Anonymní 24.10.2016
A dual module that offers a number of possibilities. I use it to adjust the gate time of a clock signal or to divide down the clock signal (these are both done with just the gate length control). With a logic module interesting rhythms can be created very simply and with asymetrical patterns or swing. I also use it to add delayed vibrato and other modulations to my sounds. The delay can be exceptionally long as can the gate length. And of course the all important LEDs to let you know what the module is doing.

I have only rated the sound as okay as this module doesn't produce or modify sounds itself (although if you put an audio signal through it you get a really crunched up distortion!)
2
0
Ohlásit hodnocení

Ohlásit hodnocení

google translate gb
Bohužel se vyskyla chyba. Zopakujte protím tuto akci později.
d
Eindelijk
dhoinjo 18.04.2019
Blij dat ik dit geprobeerd heb. Sommige van mijn sequencers sturen de gate iets te vroeg waardoor het voltage nog niet helemaal stabiel is en resulteert in ongewenste noten. Met deze module is dat verleden tijd. En dat is maar een van de mogelijkheden. Goedkoop bovendien. No brainer!
Ovládání
Vlastnosti
Zpracování
0
0
Ohlásit hodnocení

Ohlásit hodnocení

google translate gb
Bohužel se vyskyla chyba. Zopakujte protím tuto akci později.
e
Good
exmojoao 19.02.2020
It works fine i use it too to convert a longer gate into trigger with delay and length at minimum.
Ovládání
Vlastnosti
Zpracování
0
0
Ohlásit hodnocení

Ohlásit hodnocení